Lathe Machinist

Are you looking for a family owned company where the owners still treat you like family?

This Milwaukee based company is looking for a turning machinist to setup and operate in a job shop environment. NO PRODUCTION, just 1-2 piece orders mostly.

Programming in M&G Code at the machine is a HUGE plus but not required as long as you understand the program and can edit it when need be.

Starting pay is DOE but usually in the $25-27+/HR range, possibly more, especially if you can program.

Could be 1st shift opportunity or a position with a later start as it could be a non-traditional split 1st/2nd

Welder/Fabricator

We are seeking someone that can MIG and/or TIG Weld on thin to medium gauge material. The ability to TIG weld would be a plus also. They have both production and also fitter/fabricator positions available on material in the 1/2″ or thinner range depending on the job.

Job Requirements:

  • High School diploma or equivalent and 2+ years of welding experience
  • Must have the ability to read a welding blueprint
  • Must have good problem solving and critical thinking ability

Pay Rate: $20-30 per hour depending on talent level and previous experience
Days/Hours: M – F 1st Shift, 2nd and 3rd shift is available currently
* Overtime offered but not required

Maintenance Electrician

We are looking to hire an experienced Maintenance Electrician to look after the electrical system of our building. As a Maintenance Electrician, you will be required to conduct general maintenance inspections, perform routine electrical maintenance, respond to faults and wiring issues, and install major electrical appliances for the building.

Job Responsibilities:

  • Routinely inspecting electrical systems such as wiring, fixtures, and appliances.
  • Identifying faults or hazards.
  • Troubleshooting system failures.
  • Reviewing blueprints to understand wiring placement.
  • Testing of electrical systems with oscilloscopes, voltmeters, and ohmmeters.
  • Conducting maintenance repairs on old or faulty fixtures.
  • Responding to fault requests.
  • Providing suggestions for equipment replacement.
  • Writing electrical maintenance reports.
  • Installing new electrical appliances in the building.
  • Adhering to safety and performance standards.

Job requirements:

  • High school diploma or GED.
  • Electrician qualification certificate.
  • Proven work experience as a Maintenance Electrician.
  • Familiarity with industrial electrical systems and the National Electrical Code.
  • Good problem-solving skills.
  • Physically strong and able to stand for long periods.
  • Good communication skills.

Pay Rate: $34k-59k per year

Days/Hours (shift): Monday- Friday(8am-5pm)(3:30pm-11:30pm) 

*Hours are subject to change depending on workload, must be flexible.

Maintenance Mechanic

We are looking for a skilled Maintenance Mechanic to install, repair, and maintain machinery and equipment. The Maintenance Mechanic’s responsibilities include performing regular inspections of machinery and equipment, carrying out preventative maintenance, and fulfilling other duties such as building maintenance as assigned

Job Responsibilities:

  • Assembling, installing, and maintaining mechanical systems, machinery, and equipment.
  • Troubleshooting machinery and performing routine preventative maintenance.
  • Reading, interpreting, and following instructions and operation manuals.
  • Maintaining a schedule for inspecting, servicing, and testing machinery.
  • Cleaning, repairing and installing equipment and parts as needed.
  • Operating a variety of hand and power tools.
  • Maintaining a clean and organized work area.
  • Complying with health and safety regulations.
  • Performing general maintenance work on buildings as assigned.

Job requirements:

  • High school diploma/GED.
  • 2+ years of experience as a Maintenance Mechanic or in a similar role.
  • Trade or vocational school graduation preferred.
  • Knowledge and ability to operate hand and power tools.
  • Mechanical aptitude and ability.
  • Strong computer skills.
  • Physical dexterity.
  • Good troubleshooting skills.
  • Knowledge of health and safety regulations.

Pay Rate: $16-29 per hour

Days/Hours (shift): Monday- Friday(8am-5pm)(3:30pm-11:30pm) 

*Hours are subject to change depending on workload, must be flexible.

Electrical Assembler/Panel Wirer

We are seeking an Electrical Panel Wirer who is responsible for panel wiring and field routing of wire harness to motor, heater, sensors, etc. as well as proper grounding practices / device grounding practice

Job Responsibilities:

  • Operate machinery, equipment, and computer terminals
  • Test, Troubleshoot and correct panel
  • Make sure wires are tie wrapped and neatly inserted in enclosures.
  • Complete electrical panels on time
  • Machine wiring “a huge plus”
  • Visually inspect and reject parts outside of written specifications
  • Effectively wire a variety of products that range from standardized design and function to non-standard products
  • Operate within standard operating procedures (SOPs), position overview, wiring diagrams, schematics, blue prints, and work instructions
  • Use proper tools as needed to crimp wires and create harnesses
  • Complete daily production and quality logs and labor cards

Job requirements:

  • High school diploma or equivalent, with a preference for trade school training and/or 1+ years of related experience
  • Experience using Electrical Schematics
  • Proven electrical and mechanical aptitude
  •  Knowledge of Quality inspection principles
  • Use of hand tools, power tools, and electrical testing equipment
  • Self-starter and willing to accept new challenges

Pay Rate: $16-20 per hour

Days/Hours (shift): Monday- Friday(8am-5pm)(3:30pm-11:30pm) 

*Hours are subject to change depending on work load, must be flexible.

Mechanical Assembler

We are seeking a Mechanical Assembler who is responsible for completing mechanical builds or operations to print and sales order, throughout the manufacturing process.

Job Responsibilities:

  • Assemble machinery and components off custom blueprints
  • Operate hand and power tools to fabricate parts
  • Keep work station clean and organized Requirements: 
  • Ability to read blueprints
  • Ability to operate hand and power tools
  •  Use a variety of precision measuring devices to set up and adjust parts and verify conformance of work
  • Troubleshoot basic assembly problems.
  •  Perform general preventive maintenance work on tools and equipment.

Job requirements:

  • Requires high school diploma (or equivalent) plus three to five years’ related experience.
  • Must be familiar with portable power tool and machine tools such as drill press, band saw, cut-off saw and grinder.
  • Ability to read and understand documents such as blueprints, operating and maintenance instructions, and procedure manuals. Basic familiarity with G.D.&T. helpful but not required
  • Ability to write standard documentation & comfortable with documenting on a computer
  • Ability to communicate effectively (oral and written) with other employees of the organization in a quick and accurate manor.
  • Requires mathematical skills that require the ability to add, subtract, multiply and divide. Must perform metric conversions.
  • Ability to apply commonsense understanding to carry out instructions furnished in written, oral, or visual formats.
  • Basic knowledge of carpentry and \ or pneumatics is beneficial but not require

Pay Rate: $22k-40kper year

Days/Hours (shift): Monday- Friday(8am-5pm)(3:30pm-11:30pm) 

*Hours are subject to change depending on workload, must be flexible.

//www.staffpros.com/wp-content/uploads/2021/03/Site-Logo-REF.png

Milwaukee’s best Staffing Company.

2457 N Mayfair Rd, STE 200, Wauwatosa WI 53226

(414) 258-2272

info@staffpros.com

Job Alerts

Enter your email address here always to be updated. We promise not to spam!

en_USEnglish